InspirationFX: Dragonfly Links


Dragonfly Links

by: Anne Marie Desaulniers

Dragonflies
flit through the air, bringing light, wisdom, transformation, change
and adaptability to your life. At least in a symbolic sense! My
dragonflies are linked with chains, but still give a lasting impression
of daydreams, light and movement! If you only made a wish, I’m sure
that something magical would happen!
This two-strand necklace
is full of movement and grace! In my original plans (which often go
astray), it was going to be three-strands, and tied off with a red, silk
strand. My muse said “enough”, after I completed the second strand,
and then totally scoffed at the red silk. The colour wasn’t quite right,
and the piece obviously needed more “weight” to anchor the design. So I
dipped into my stash, and came up with a short piece of chain, to
finish it off with style!

Top Strand:

Four wrapped loop components, with wraps on both ends, three pieces of “Throw me a Curve” chain, and four dangle components.

Wrapped loop component – three 6/0 Seedbeads/one druk/one metal round/one druk/three 6/0 Seedbeads (make a total of four).

Dangle
component – add one druk and one 6/0 seedbead onto Ball headpin. Make
small wire wrapped loop on the end (make a total of four).

Attach
as follows: oval jump ring/W loop component/oval jump ring/chain (3
curves)/oval jump ring/W loop component/oval jump ring/chain (3
curves)/oval jump ring/W loop component/oval jump ring/chain (3
curves)/oval jump ring/W loop component/oval jump ring.
Attach
four dangles to middle section of chain, with oval jump rings. Attach
to jump rings on either end, and to loops on either side of middle curve
in chain. Do not attach directly to the curved areas, as the dangles
will not stay neatly in place (ask me how I know?).

Bottom Strand:

Five
wrapped dragonfly (DF) coin loop components, with wraps on both ends,
four, four-sun, chain components, two, two-sun chain components, and
four dangle components.

Wrapped DF loop component – one 6/0 seedbead/one DF coin bead/one 6/0 seedbead (make a total of five).

Dangle
component – add one druk and one 6/0 seedbead onto Ball headpin. Make
small wire wrapped loop on the end (make a total of four).

Attach
as follows: oval jump ring/one two-sun chain component/one W DF coin
loop component/oval jump ring/one four-sun chain component/oval jump
ring/one W DF coin loop component/oval jump ring/one four-sun chain
component/oval jump ring/one W DF coin loop component/oval jump ring/one
four-sun chain component/oval jump ring/one W DF coin loop
component/oval jump ring/one four-sun chain component/oval jump ring/one
W DF coin loop component/oval jump ring/one two-sun chain
component/oval jump ring.

Attach dangles to either side
of middle W DF coin loop component with oval jump rings. Then attach
one dangle to W DF coin loop component, on the left of the middle
component (with oval jump ring). Next, you will attach the final dangle
to the W DF coin loop component, on the right of the middle component
(with oval jump ring). Note: I chose to attach the dangles to the W
loops, but it might be better to actually attach them to the oval jump
rings (the choice is yours!).

Pulling it all together:

Attach the first side of Strand One to one-13 mm-open circle, with a 7 mm round jump ring.
Attach the second side of Strand One to one-13 mm-open Circle, with a 7 mm round jump ring.
Attach the first side of Strand Two to one-13 mm-open circle, with a 7 mm round jump ring.
Attach the second side of Strand Two to one-13 mm-open circle, with a 7 mm round jump ring.
Attach the first open circle to a 2 – inch piece of Rolo chain.
Attach the second open circle to a 2 – inch piece of Rolo chain.
Attach Hook Clasp to right side of Rolo chain, with a 7mm round jump ring.
Attach Swivel/Rotating Link to the left side of Rolo chain, with a 7 mm round jump ring.

If
you don’t know how to make wrapped loops, check out our “Tips” section,
take a class, buy a book or magazine, Google it, or watch a video. The
real secret is practice, so just get out there and do it!!
Tools used:

Flush cutters
Chain nose pliers
Round nose pliers

Show
the world your carefree side, by either dressing this necklace up or
down. Pair it with silk, linen, cotton, chambray, lace or even leather.
Perhaps a little bohemian, but definitely perfect for someone wishing
to make a quiet statement!

Components

Go to our components list for this project and to buy what you need!
Need some help with some of the techniques? Check our tips page.

2 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *


By submitting this form, you are consenting to receive marketing emails from: beadFX Inc., 19 Waterman Ave., Unit #2, Toronto, ON, M4B 1Y2, http://www.beadfx.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact